主页 / unix / 问题 / 460587
Accepted
Guerlando OCs
Asked: 2018-08-05 20:44:20 +0800 CST

创建一个接入点以在两个无线连接之间“桥接”。/etc/network/interfaces 应该怎么看？

  • 772

我正在遵循本指南：将 Raspberry Pi 设置为独立网络 (NAT)中的接入点以创建接入点。唯一的区别是我正在使用以太网连接所在的另一个 wifi 连接，所以我只是在整个教程中进行了更改，因为eth0我的 USB 加密狗连接到我的路由器。wlan1wlan1

但是，没有关于该/etc/network/interfaces文件的任何内容。这是我的：

auto wlan0
allow-hotplug wlan0
iface wlan0 inet dhcp
#wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf

auto wlan1
allow-hotplug wlan1
iface wlan1 inet dhcp
wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf

我可以看到 SSID 并连接到它，但它会一直获取 IP 地址。我认为这与/etc/network/interfaces. 看看我的ifconfig：

pi@raspberrypi:~ $ ifconfig 
lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 4  bytes 156 (156.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 4  bytes 156 (156.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.25.6  netmask 255.255.255.0  broadcast 192.168.25.255
        inet6 fe80::ba27:ebff:feaa:1f8  prefixlen 64  scopeid 0x20<link>
        ether b8:27:eb:aa:01:f8  txqueuelen 1000  (Ethernet)
        RX packets 42  bytes 5757 (5.6 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 37  bytes 5838 (5.7 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.25.6  netmask 255.255.255.0  broadcast 192.168.25.255
        inet6 2804:7f0:e181:b678:2e0:4dff:fe06:4f8  prefixlen 64  scopeid 0x0<global>
        inet6 fe80::2e0:4dff:fe06:4f8  prefixlen 64  scopeid 0x20<link>
        ether 00:e0:4d:06:04:f8  txqueuelen 1000  (Ethernet)
        RX packets 86  bytes 11978 (11.6 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 86  bytes 15855 (15.4 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

怎么wlan0会有IP 192.168.25.6？这是wlan1连接的路由器提供的 IP。

我应该如何编辑wlan0配置？我一直在尝试很多静态配置，但是当我做任何不同于屏幕上的操作时，板载 wifi 接口消失，然后 USB 加密狗取代了wlan0.

另外，有没有办法保证usb dongle总是能得到wlan1和板载wifi wlan0？似乎随意。

更新

● dhcpcd.service - dhcpcd on all interfaces
   Loaded: loaded (/lib/systemd/system/dhcpcd.service; enabled; vendor preset: enabled)
  Drop-In: /etc/systemd/system/dhcpcd.service.d
           └─wait.conf
   Active: failed (Result: exit-code) since Sun 2018-08-05 04:54:32 UTC; 7s ago
  Process: 853 ExecStart=/usr/lib/dhcpcd5/dhcpcd -q -w (code=exited, status=6)

Aug 05 04:54:32 raspberrypi systemd[1]: Starting dhcpcd on all interfaces...
Aug 05 04:54:32 raspberrypi dhcpcd[853]: Not running dhcpcd because /etc/network/interfaces
Aug 05 04:54:32 raspberrypi dhcpcd[853]: defines some interfaces that will use a
Aug 05 04:54:32 raspberrypi dhcpcd[853]: DHCP client or static address
Aug 05 04:54:32 raspberrypi systemd[1]: dhcpcd.service: Control process exited, code=exited status=6
Aug 05 04:54:32 raspberrypi systemd[1]: Failed to start dhcpcd on all interfaces.
Aug 05 04:54:32 raspberrypi systemd[1]: dhcpcd.service: Unit entered failed state.
Aug 05 04:54:32 raspberrypi systemd[1]: dhcpcd.service: Failed with result 'exit-code'.
networking wifi

1 个回答

  1. Best Answer

    如果wlan0要成为接入点 (AP)，则不应尝试将其用作客户端（站、STA）。但这就是

    auto wlan0
allow-hotplug wlan0
iface wlan0 inet dhcp
#wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf

    说：“请wlan0在客户端模式下使用，并使用 DHCP 为其获取 IP 地址”。相反，你想要类似的东西

    auto wlan0
iface wlan0 inet static
address 10.0.0.1
netmask 255.255.255.0
broadcast 10.0.0.255

    10.0.0.*用您希望为 AP 设置的 IP 范围替换和网络掩码。

    • 1

相关问题