我的风扇有噪音问题。之后pwmconfig，我发现从 120 到 255（我猜这些被称为 pwm 速度），大多数都是损坏的。有什么办法可以修复它吗？任何应用程序？对 linux 和 windows 应用程序都很好。对不起，如果无法正确解释并提前感谢。
编辑-1
PWM 255 FAN 1962
PWM 240 FAN 1467
PWM 225 FAN 2385 (probably incorrect)
PWM 210 FAN 3245 (probably incorrect)
PWM 195 FAN 3013 (probably incorrect)
PWM 180 FAN 2755 (probably incorrect)
PWM 165 FAN 2436 (probably incorrect)
PWM 150 FAN 2136 (probably incorrect)
PWM 135 FAN 1790 (probably incorrect)
PWM 120 FAN 1486
PWM 105 FAN 1397
PWM 90 FAN 1344
PWM 75 FAN 1290
PWM 60 FAN 1247
PWM 45 FAN 1201
PWM 30 FAN 1171
PWM 28 FAN 1165
PWM 26 FAN 1161
PWM 24 FAN 1157
PWM 22 FAN 1153
PWM 20 FAN 1149
PWM 18 FAN 1146
PWM 16 FAN 1144
PWM 14 FAN 1140
PWM 12 FAN 1134
PWM 10 FAN 1134
PWM 8 FAN 1130
PWM 6 FAN 1128
PWM 4 FAN 1123
PWM 2 FAN 1121
PWM 0 FAN 1117
想控制我的风扇速度。试过pwmconfig但没有用。
我明白了
hwmon1/pwm3 is currently setup for automatic speed control
这个（hwmon1/pwm3）是我的噪音制造者。在手动模式下需要它，并且在最后pwmconfig，缺少配置选项，我的意思是在 5 个选项中，我只得到 4 个，而且 /etc/fancontrol 似乎是空的。
编辑-2
sudo pwmconfig
[sudo] password for seebox:
# pwmconfig version 3.6.0
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.
We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.
Found the following devices:
hwmon0 is coretemp
hwmon1 is it8718
Found the following PWM controls:
hwmon1/pwm1 current value: 254
hwmon1/pwm2 current value: 254
hwmon1/pwm3 current value: 254
hwmon1/pwm3 is currently setup for automatic speed control.
In general, automatic mode is preferred over manual mode, as
it is more efficient and it reacts faster. Are you sure that
you want to setup this output for manual control? (n) yes
Giving the fans some time to reach full speed...
Found the following fan sensors:
hwmon1/fan1_input current speed: 4218 RPM
hwmon1/fan2_input current speed: 0 ... skipping!
Warning!!! This program will stop your fans, one at a time,
for approximately 5 seconds each!!!
This may cause your processor temperature to rise!!!
If you do not want to do this hit control-C now!!!
Hit return to continue:
Testing pwm control hwmon1/pwm1 ...
hwmon1/fan1_input ... speed was 4218 now 3358
no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon1/pwm1,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)? n
Testing pwm control hwmon1/pwm2 ...
hwmon1/fan1_input ... speed was 4218 now 3169
no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon1/pwm2,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)? n
Testing is complete.
Please verify that all fans have returned to their normal speed.
The fancontrol script can automatically respond to temperature changes
of your system by changing fanspeeds.
Do you want to set up its configuration file now (y)? y
What should be the path to your fancontrol config file (/etc/fancontrol)?
Loading configuration from /etc/fancontrol ...
Select fan output to configure, or other action:
1) Change INTERVAL 3) Save and quit
2) Just quit 4) Show configuration
select (1-n):