Recentemente instalei o Debian Stable 12.7 e ele está funcionando muito bem. Tentei conectar um disco rígido externo (presumo que ele tenha partição NTFS). A luz no disco rígido acende, ele começa a zumbir, mas não conecta. A seguir está a saída do comando 'dmesg':
[ 299.027072] ISO 9660 Extensions: Microsoft Joliet Level 1
[ 299.030692] ISOFS: changing to secondary root
[ 461.519421] usb 1-1.3.3: USB disconnect, device number 5
[ 461.780067] usb 1-1.3.3: new high-speed USB device number 6 using ehci-pci
[ 461.888648] usb 1-1.3.3: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.00
[ 461.888656] usb 1-1.3.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 461.888660] usb 1-1.3.3: Product: USB2.0 HUB
[ 461.889073] hub 1-1.3.3:1.0: USB hub found
[ 461.889248] hub 1-1.3.3:1.0: 4 ports detected
[ 462.612070] usb 1-1.3.3.3: new high-speed USB device number 7 using ehci-pci
[ 462.821973] usb 1-1.3.3.3: New USB device found, idVendor=1058, idProduct=2626, bcdDevice=10.34
[ 462.821981] usb 1-1.3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 462.821985] usb 1-1.3.3.3: Product: My Passport 2626
[ 462.821987] usb 1-1.3.3.3: Manufacturer: Western Digital
[ 462.821989] usb 1-1.3.3.3: SerialNumber: 575832324139335238333439
[ 462.871255] usb-storage 1-1.3.3.3:1.0: USB Mass Storage device detected
[ 462.871439] scsi host6: usb-storage 1-1.3.3.3:1.0
[ 462.871558] usbcore: registered new interface driver usb-storage
[ 462.878172] usbcore: registered new interface driver uas
[ 463.889586] scsi 6:0:0:0: Direct-Access WD My Passport 2626 1034 PQ: 0 ANSI: 6
[ 463.890390] scsi 6:0:0:1: Enclosure WD SES Device 1034 PQ: 0 ANSI: 6
[ 463.900858] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 463.901059] scsi 6:0:0:1: Attached scsi generic sg4 type 13
[ 463.904605] sd 6:0:0:0: [sdc] Spinning up disk...
[ 464.912081] ..................................................................................................not responding...
[ 576.243597] sd 6:0:0:0: [sdc] Read Capacity(10) failed: Result: hostbyte=DID_OK driverbyte=DRIVER_OK
[ 576.243607] sd 6:0:0:0: [sdc] Sense Key : Not Ready [current]
[ 576.243610] sd 6:0:0:0: [sdc] Add. Sense: Logical unit is in process of becoming ready
[ 578.244590] sd 6:0:0:0: [sdc] 0 512-byte logical blocks: (0 B/0 B)
[ 578.244599] sd 6:0:0:0: [sdc] 0-byte physical blocks
[ 580.245617] sd 6:0:0:0: [sdc] Test WP failed, assume Write Enabled
[ 582.246626] sd 6:0:0:0: [sdc] Asking for cache data failed
[ 582.246639] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 582.247059] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 596.259393] scsi 6:0:0:1: Failed to get diagnostic page 0x1
[ 596.259405] scsi 6:0:0:1: Failed to bind enclosure -19
[ 596.259435] ses 6:0:0:1: Attached Enclosure device
Qual é o problema e como ele pode ser resolvido?
O disco não está respondendo aos comandos. Não há uma maneira de software para resolver isso; certifique-se de que a energia fornecida seja suficiente; você pode tentar um gabinete externo diferente com o mesmo disco, caso contrário, assuma que o disco está fisicamente quebrado.